What does it mean when the check engine light comes on?
It means your car's computer found a fault in a system it monitors, usually something tied to the engine, fuel, ignition, or emissions. The light itself doesn't say what failed. It says "something here needs a look."
Every time you turn the key, the light should flash on briefly and then go out once the engine is running. That short flash is the system checking itself. If it never comes on at startup, the bulb or circuit may be bad, and that can be a problem at smog time too.
Sometimes the light turns itself off after a few trips. That usually means the condition that set it went away, not that the system is broken. It's still worth having the stored code checked if it keeps coming back.
Solid or flashing: what's the difference?
A solid light means a problem worth diagnosing soon. A flashing light means a severe problem, such as a misfire, that should be handled right away.
| What you see | What it usually means | What to do |
|---|---|---|
| Brief flash at startup, then off | Normal system self check | Nothing |
| Solid light while driving | The car may not be running properly; it could waste fuel or shorten engine life | Check the gas cap, then schedule a diagnostic soon |
| Flashing light while driving | A severe problem, often an engine misfire | Limit driving, avoid high speeds and heavy loads, and get it checked right away |
This guidance comes from the EPA's consumer fact sheet, What to Do With the Check Engine Light.
What are the most common causes of a check engine light?
The light can point to dozens of faults, but these are the ones we see behind smog fails and drivability complaints most often:
- A loose or missing gas cap. The easiest fix, and the first thing to check.
- An oxygen sensor. It reads exhaust and helps the engine set its fuel mix.
- The catalytic converter. It cleans exhaust, and a failing one often sets a code.
- An evaporative emissions (EVAP) leak. A leak in the system that traps fuel vapor.
- Misfires and worn ignition parts. Spark plugs, coils, or wires that aren't firing right.
The code tells us which system flagged the fault. Testing tells us which part actually failed. Those two things aren't always the same.
What should you do when the check engine light comes on?
Stay calm, check the gas cap, and schedule a diagnosis. Here's the order we'd follow:
- Don't panic. The car will usually keep running. Note whether the light is solid or flashing.
- If it's flashing, slow down. Limit driving and avoid high speeds and heavy loads.
- Check the gas cap when you stop. Make sure it isn't loose or missing, and never refuel with the engine running.
- Pay attention to how the car feels. Rough idle, hesitation, a new smell, or a temperature gauge climbing are all worth mentioning.
- Schedule a diagnostic. The sooner it's tested, the more likely it stays a smaller repair.
Get the real answer, not just a code.
We test it, explain it in plain language, and wait for your decision.
5899 Lindhurst Ave, Marysville · Monday to Thursday, 7 AM to 6 PM
Is a free code read the same as a diagnostic?
No. A code read tells you which system set the light. A diagnostic finds out why.
A misfire code, for example, can come from a plug, a coil, an injector, a vacuum leak, or low compression. Replacing parts based on the code alone is how people end up paying for two or three repairs to fix one problem.
You might be wondering if we'll find a list of extra things to fix.
Here's the truth: we test the system that set the light and explain the results so you can make the call. If something else needs attention, we'll tell you what it is and how urgent it is, and you decide what to do and when.
You might be wondering if you can just keep driving.
Here's the truth: with a solid light and a car that feels normal, you usually can for a short time. With a flashing light, the EPA's advice is to limit driving and get it handled quickly. Either way, a light left on for months tends to cost more in the end.
Will a check engine light fail a California smog check?
Yes. California's Bureau of Automotive Repair fails an OBD II vehicle if the check engine light stays on with the engine running. It also fails a car whose light doesn't come on at all when the key is turned on and the engine is off.
Clearing the codes won't sneak you through either. Clearing codes or disconnecting the battery resets the car's readiness monitors, and BAR's OBD test reference notes the monitors must run again after repairs like a battery disconnect. On 2000 and newer gas vehicles, only the EVAP monitor is allowed to be incomplete.
If your registration is coming up, our failed smog check guide walks through the next steps, and because smog check is one of our auto repair services, you can test and repair in the same shop.
What happens during a diagnostic at Boradori Automotive?
A diagnostic at Boradori Automotive tests the car, summarizes its current condition, and lays out the next steps in plain language.
- Tell us what you noticed. Solid or flashing, when it came on, and anything the car is doing differently.
- We read the codes and test the system. Our technicians pair hands on experience with current diagnostic technology to trace the fault to its cause.
- We look at the bigger picture. Our diagnostics cover engine performance, braking, electrical systems, and more, so small problems get caught early.
- We explain it in plain language. You get a summary of what we found and what we recommend.
- You decide. Repairs happen only when you choose them.
More on how we work is on our diagnostics page. If the cause turns out to be deeper in the motor, our engine repair team takes it from there.